Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Hinge & Roller Replacement: The San Fernando Owner’s Guide
We stock and install FAAC-compatible hinge and roller replacements for sliding and swing gates across San Fernando, with typical installed pricing running $165 to $380 per hinge or roller set. Most replacements are completed the same day we arrive, and every job carries our written 90-Day Done Right Promise. You usually discover the problem before you see it: the gate starts to grind, lean, or bind about two-thirds through its travel, and by the time you look closely, the roller has a flat spot or the hinge pin has worn into an oval.
Which FAAC Models This Applies To
We replace hinges and rollers across the FAAC sliding gate range here in San Fernando, including the 740, 741, 750, 760, 770, 844, and 884 series that are common on older estate lots throughout the valley. The compatibility gotcha most owners don’t know is that FAAC uses two distinct roller profiles: a narrower V-groove on the 740/750 series and a wider U-groove on the 844/884 line, and they are not interchangeable. If you match the wrong roller to the track, the gate will ride high and chatter every cycle. We pull the part, measure the groove width and wheel diameter against the track profile, and match it with either the OEM FAAC part or a quality aftermarket equivalent when it makes more sense for the age of the gate. For FAAC specifically, the OEM hinge with a greasable pin is worth the extra cost on a gate that sees daily cycles; on a rarely-used side gate, a well-made aftermarket hinge at half the price does the job and we’ll tell you that straight.
Signs Your FAAC Hinge & Roller Replacement Is Failing
- Grinding or rumbling as the gate travels. The roller bearing is breaking down, usually on the wheel that carries the most weight. Out here in San Fernando’s dry summer heat, the grease in a sealed bearing cooks off years before the wheel actually fails.
- Gate sags at the free end. A hinge pin has worn into an oval and the gate leaf is now riding on the bottom edge of the frame instead of the hinge. On a 16-foot FAAC gate, half an inch of hinge pin wear turns into six inches of sag at the end.
- Noticeable side-to-side wobble or shake. The roller has developed a flat spot from sitting parked in the same position year after year. Once a flat spot forms, the wheel never rolls cleanly again, even if you grease it.
- Gap changes at the closed position. The gate used to kiss the stop post evenly and now leaves a wider gap at the bottom or top. That’s hinge wear on swing gates, and roller wear on sliders.
- Squeaking that no amount of spray lube fixes. A squeak that comes back every week is a dry or scored hinge pin, not a maintenance issue. The only fix that holds is a new hinge with a properly greased pin.
Replacement Cost & What’s Included
In San Fernando, plan on $165 to $380 per hinge or roller set installed, depending on the FAAC series, the number of points being replaced, and whether we’re swapping just the wheel or the full hinge bracket assembly. A single failing roller on a 750 series typically runs $165 to $210 with labor; a full hinge pair with greasable pins on a heavier 884 swing gate runs $280 to $380. We quote the part and labor separately so you know exactly what you’re paying for, and the price is settled before a single bolt is turned. You’ll never get a surprise on the bill. Every replacement is covered in writing by our 90-Day Done Right Promise: if it’s not right, we come back and make it right, no arguing, no paperwork.
DIY or Call Us?
Here’s the honest split. You can safely watch the gate run and tell us exactly what you’re seeing and hearing. But replacing a hinge or roller on a FAAC gate means taking weight off the structure, and that’s where DIY goes wrong. The gate leaf is heavy, often 400 to 700 pounds on a San Fernando driveway, and even a few inches of movement under load will hurt you. The roller brackets are often welded or seized in place on older FAAC installations, and the gate must be re-squared after the swap or the motor strains against the new geometry. One caution whether you call us or anyone: never prop a sliding gate and reach between the leaf and the track. Call (925) 307-8328 and we’ll be there when we say.
FAQs
You’ll get 8 to 14 years from a FAAC roller in our climate, with the southwest-facing gate on the hotter side of the property wearing a year or two faster because heat kills bearing grease. Hinges with greasable pins last 15 to 20 years when serviced annually; sealed hinges that can’t be greased typically fail in half that time.
Sometimes. If the wheel itself is sound and the bracket isn’t cracked, we can press in a new bearing and a fresh wheel on many FAAC series. But when the V-groove is worn from riding the track, the bracket is the problem and the whole roller gets swapped. We’ll show you the part when we’re done so you can see exactly what was replaced. Call (925) 307-8328 and we’ll give you a straight answer on your specific gate.
Most single-point roller replacements take under an hour. A full hinge pair with re-squaring on a heavy FAAC swing gate runs two to three hours. We complete most jobs in a single visit because we arrive with the right parts on the truck, and we’ll tell you the timeline before we start.
Yes. We keep the common FAAC 740, 750, 760, 770, 844, and 884 series rollers and hinge pins on hand, along with the tools to press bearings and re-square the leaf on site. If your gate needs a less common part, we order it and return quickly. We also service LiftMaster, Mighty Mule, and Ghost Controls parts when a home has a mixed opener setup.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving San Fernando and nearby areas.