Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for San Fernando Homeowners
A new driveway gate in San Fernando typically costs between $3,200 and $9,800 installed, and most jobs run two to four days from first measurement to final walk-through. That’s the honest range, and if you’ve lived here through a few summers, you know why it varies: setbacks, slope, soil, and the kind of gate you want all move the number. We’re Ironworks Gate Co., and we’ve been putting gates in for San Fernando homeowners since 1984. Led by Victor Salinas, our installers are background-checked and uniformed, and every job carries our written 90-Day Done Right Promise. Call (925) 307-8328 for a free estimate; we answer the phone around the clock.
What Our Gate Installation Service Includes
Gate installation is more than setting a post and hanging a panel. It means accounting for the driveway grade, the way the sun hits the motor in August, and the swing arc a double gate needs before the first hole is dug. Here’s what a new gate from Ironworks Gate Co. covers, broken down by type.
Driveway Gate
A driveway gate is the main entry gate for your vehicles, typically spanning 10 to 24 feet depending on the number of cars and the width of the apron. In San Fernando, where many homes on Brand Boulevard and the neighborhoods around San Fernando Road sit on lots that slope gently toward the street, the gate’s clearance and opening direction matter more than homeowners expect. That’s why our Gate Installation in San Fernando always starts with an in-person measure. We measure every job in person, fabricate or order the gate to fit, and set the hinges and motor so the gate holds square through years of use.
Pedestrian Gate
A pedestrian gate is the smaller walk-through gate beside or built into a larger driveway gate, and it’s the one your family and delivery drivers will use daily. We weld and install these to match the driveway gate in material and finish, including the self-closing hardware that keeps it from banging open in the wind. If the path between your house and the sidewalk is narrow, we adjust the swing and latch so it clears cleanly every time.
Sliding Gate
Sliding gates travel sideways along a track instead of swinging out, making them the right choice when you have a short driveway apron or limited space for a swing arc. Many homes in the Pacoima Wash area and along Glenoaks Boulevard, as well as nearby Sylmar Gate Installation sites, have driveways that rise quickly from the street, which shortens the flat area a swinging gate needs. We install and align cantilever and track-style sliding gates, including the rollers, guides, and motor mounting so the gate travels smoothly without binding.
Swing Gate
Swing gates open inward or outward on heavy hinges, and they remain the most common choice in San Fernando because of the look and the simplicity. A swing gate gives you the classic estate entry, but it also puts real stress on the posts, which is why we set them in concrete and reinforce the hinge points with welded plates. Whether single or double, we calculate the arc so a parked car on the driveway never clips the gate.
Double Gate
Double gates are two panels that meet in the middle, and they’re the answer when your driveway is wide enough that a single leaf would be too heavy or too slow. San Fernando lots with RV access or wider side yards nearly always do better with a double gate. For the Best Gate Installation in San Fernando, CA, we make sure both leaves meet dead center. We install the center stop, post alignments, and helper hardware like drop rods and cane bolts so both leaves meet dead center without sagging, and we set the opener to sequence the panels correctly.
Security Gate
A security gate is engineered for more than curb appeal, with reinforced framing, pickets set closer together, and often a stronger opener with anti-tailgating functions. For San Fernando homeowners who’ve had equipment stolen from a driveway or want the back lot enclosed, a security gate is the call. We also offer Emergency Gate Installation in San Fernando, CA when security can’t wait. We work with the heavier steel and pair it with operators rated for the extra weight, and we add the close-limit settings that prevent the gate from resting open.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We stock OEM parts and factory training on DoorKing equipment, which we’ve put in on everything from light residential swing gates to heavier commercial-style slide applications. A DoorKing operator is a common fit for gates in the San Fernando area because of its track record, and we know the start/stop timing and limit adjustments on those boards the way a mechanic knows an engine he’s worked on for decades.
We also install and mate new gates to Ghost Controls openers, which we like for single-family swing and slide setups where you want a battery backup without a separate cabinet. And when the job calls for a heavier gate with solar or high-cycle use, we turn to Elite operators, whose arm-style actuators hold up in the heat. Whether you have one of these makes or something else on the driveway, we’ll spec the gate and the automation to each other so the whole system works as one unit.
Signs You Need Gate Installation Right Now
- Your posts are rotting or leaning, not bending. A wood post that flexes at the base or shows a crack at the hinge is past adjusting. Once the post moves, the gate can’t hold square, every cycle grinds the hinges and latches harder, and it’s usually cheaper in the long run to pull and replace the full set than to nurse a post along.
- The gate groans on every swing and the hinges have play. When you can lift the gate an inch at the hinge, the pin’s worn or the barrel’s wallowed out. Continuing to use it strains the opener and wears the latch, and a gate that binds mid-swing is a safety hazard, especially with kids around.
- You’ve added a car, a trailer, or an RV to the household. A driveway that fit two cars five years ago may not fit today’s wider truck or the trailer you use on weekends. If the gate has to be fully open before you can complete your turn off the street, you’re a candidate for a wider or sliding gate that matches the current driveway geometry.
- You don’t have a gate at all, and your street sees foot traffic. Homes near the San Fernando Mall and the bus stops on Truman Street get more walk-through traffic than people expect. A driveway gate and a locking pedestrian gate close the gap between the sidewalk and your property line, and they tell a would-be prowler to keep walking.
- The opener is dead, and the gate is nearly 20 years old. A failed motor on a gate with rusty panels, welded repairs, and a frame that’s been patched twice is often not worth the cost of a new opener bolted to the old steel. Replacing the whole assembly gets you matching hardware, a fresh warranty, and a gate that won’t need another visit for years.
Our Gate Installation Process - Step by Step
- 1
Site measure and sight line check. We walk the property with you, measure the driveway width and grade, and check the clearance you have in both directions. We look at where the gas meter, water lines, and irrigation sit along the gate path, because hitting any of those on dig day is a costly surprise.
- 2
Gate and hardware selection. Based on the measurements and how you use the driveway, we spec the gate material, panel style, hinge type, and the opener that’s matched to the gate’s weight and duty cycle. We quote you a firm price at this point, and nothing starts until you’ve seen the number and said yes.
- 3
Post setting and leveling. We dig, set, and brace the posts in concrete, then let the concrete cure enough to hold the load before any weight goes on. On a swing gate, we weld reinforcement plates at the hinge points. On a slide gate, we pour or anchor the track base and set the guide rollers level.
- 4
Gate hang, opener mounting, and travel adjustment. We hang the gate, mount the motor, and set the open and close limits, force settings, and any pedestrian-gate interlock so the system runs true. We also run the safety edges and photoeyes so the gate reverses on contact.
- 5
Final walk-through and written guarantee. Before we leave, we cycle the gate several times with you watching, show you how the manual release works, and hand you the paperwork on the 90-Day Done Right Promise. You’ll also get the opener’s factory warranty details, and we note the install date for any future service.
How Much Does Gate Installation Cost in San Fernando?
A single swing gate with a basic opener for a standard 12-foot driveway in San Fernando runs roughly $3,200 to $4,900 installed. A double swing gate with heavier steel and a mid-range motor lands between $5,500 and $7,800. Slide gates, because of the track, rollers, and extra fabrication, start around $4,500 and go past $9,000 for wider or cantilever designs. Pedestrian gates alone, matched to an existing driveway gate, generally fall between $900 and $2,100.
What moves the price is the material, the width, the opener spec, and what’s underneath the dirt. Rocky soil in the hills above San Fernando slows the dig and adds to concrete and bracing costs. Longer cantilever slide gates cost more than a swing gate on the same opening, and a battery backup or solar panel adds a few hundred. The way to avoid overpaying is to get a written quote that separates the gate, the motor, and the labor, and to have the site measurement done before any dollar is put on paper. Our estimates are free, and the price we give is the price you pay, not a starting point.
Gate Installation Near San Fernando - Our Service Area
We install gates across the San Fernando Valley and into the foothill communities around it, including Gate Installation in Sylmar, Gate Installation in Santa Clarita, Panorama City, Granada Hills, Sun Valley, Northridge, Van Nuys, Porter Ranch, Reseda, Acton, and Agua Dulce. Most San Fernando installs we can reach the same week, and a live person answers the phone 24 hours a day to schedule the visit.
Serving San Fernando, CA - Our Local Coverage Area
We’re based in the San Fernando area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in San Fernando
Gate installation is the full process of measuring your driveway or walkway opening, setting new posts, hanging a new gate, and wiring and programming the opener so the gate runs automatically. It includes the physical gate, hinges, latch, motor, safety edges, and any keypad or remote controls. At Ironworks Gate Co., we handle the whole job in-house and stand behind it with our 90-Day Done Right Promise. Call (925) 307-8328 for a free, no-obligation quote.
Most standard driveway gate installations in San Fernando are done in two to four days from measure to final walk-through, and many swing gates are up and running in one long day once the materials are in. Larger slide or double gates may run three to five days. We set the schedule when we quote, and we hit the day we promise.
Most gate installations in San Fernando run between $3,200 and $9,800, depending on the type, width, material, and opener. A simple single swing gate is at the low end, while a wide cantilever slide gate with a high-duty-cycle operator is at the top. We give you a written, itemized price before any work starts so there are no surprises. Call (925) 307-8328 for an exact quote, the estimate is free.
Yes, we regularly install and configure DoorKing openers on new San Fernando gate jobs, and we keep their OEM parts and boards on the truck. If you already have a DoorKing operator and are only replacing the gate itself, we’ll marry the new gate to the existing motor. We also work with Ghost Controls, Elite, Mighty Mule, and most other major brands.
Installation jobs are scheduled, not dispatched on an emergency basis. A new gate requires measurement, material order, and concrete work, so it cannot be done right in one rushed visit. If your existing gate has failed and needs urgent repair instead, call us any time, day or night, at (925) 307-8328 and we’ll get a technician to you and get the gate secured.
Every gate installation from Ironworks Gate Co. is covered by our written 90-Day Done Right Promise, which means if anything isn’t right, we come back and make it right at no charge. The opener and motor also carry the manufacturer’s factory warranty, and we register that for you at install. Our guarantee needs no paperwork and no arguing.
Clear the driveway and the walkway beside it so we have a full workspace, and move any vehicles out of the gate’s swing path for the day. Let us know where any irrigation lines, pet fences, or low-voltage lights run near the gate, and make sure the breaker panel has a spare circuit for the opener. We’ll handle the rest, from permits to programming.
Schedule Your Gate Installation Service in San Fernando Today
A new gate is a decision you should only have to make once. We’ll measure, quote a firm price, and install it right, and our 90-Day Done Right Promise backs every bolt. Call Ironworks Gate Co. at (925) 307-8328 for a free estimate, or visit our home page to see more. A real person answers, day or night.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving San Fernando since 1984.