Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across North Hollywood
When a driveway gate drags, jams, or stops latching in North Hollywood, the cause usually comes down to one thing: a part that has finally given out after years of Valley heat and daily use. Whether you need Gate Installation in North Hollywood or repair, we handle it. Hinge replacement, post replacement, rail repair, custom welding, gate rollers, latches, and locks: that is what we do all day, for homes and apartment courts from the 91601 corridor through 91602 and 91603. We know what fails on NoHo gates and we show up fast. If you’re dealing with a gate that won’t close or a hinge that’s pulling a post out of the concrete, call (925) 307-8328 and a live person will answer.
Why Ironworks Gate Co. Is North Hollywood’s Preferred Gate Parts & Welding Company
We have built our name in Southern California by doing one thing and doing it right: driveway and estate gates. Nothing else. That focus means our Gate Parts & Welding team shows up with the right steel, the right fasteners, the right settings on the welder, and a decade-spanning memory of what these specific North Hollywood gates tend to need. Property owners around Lankershim, Victory, and the older bungalow streets east of the 170 call us because we diagnose the actual failure, not just the symptom. The job gets quoted before any work starts. No surprises on the bill.
Victor Salinas, who leads our crews, has a simple standard: the 400th job gets the same care as the first. Every completed job is backed by the 90-Day Done Right Promise in writing. If something isn’t right, we come back and make it right. No paperwork, no arguing. That’s the Keystone Standard, and it applies to every hinge, weld, roller, and post we touch in North Hollywood.
We also know that a busted gate is a genuine problem here. It’s not like a squeaky hinge that can wait. It’s the only vehicle access to a shared court. It’s a security gap on a busy street. So we prioritize North Hollywood calls, we stock the common roller and hinge sizes on our trucks, and a live person answers our phone 24 hours a day, 7 days a week. Not a voicemail. A person.
Our Gate Parts & Welding Services in North Hollywood
Hinge Replacement
On 1950s and 1960s bungalow swing gates across North Hollywood, we commonly replace the original barrel hinges with a heavier weld-on barrel or pillow block bearing. The old hinge usually isn’t worn out from opening and closing alone; it’s been carrying a gate panel that slowly pulled the post out of plumb for thirty years. We level the gate, weld the new hinge in place, and re-latch it so the panel closes square on the strike. Most hinge replacements in North Hollywood are done same-day, and the price is settled up front.
Post Replacement
Post replacement in North Hollywood often means cutting out a hinge post that has cracked at its concrete footing and pulling the old anchor bolts with it. We do this dozens of times each year on the apartment courts and shared driveways off Lankershim and Victory. The new post gets set in a deeper footing, welded with a gusset plate at the base for lateral strength, and re-tied to the fence run. If the gate is automated, we re-mount the operator arm and check the Gate Access Control - North Hollywood limit switches before we leave.
Rail Repair
Sliding gate rails in North Hollywood take a beating. Steel tracks expand when the driveway hits 100°F or more, and if the rail was installed without enough clearance, the gate binds mid-cycle and stalls. We cut out bent or heat-warped sections and weld in new track, then re-set the gate so it rides smooth through the full travel. On older retrofits where the rail was surface-mounted on the concrete, we’ll sometimes add a shim plate to keep the rail from flexing under the gate’s weight.
Custom Welding
Not every fix comes off a shelf. For rusted post feet on a 1990s NoHo apartment gate, we cut and weld custom steel repair plates, reinforce cracked rail stanchions, and weld on new latch keepers. If a gate needs a piece that no supplier stocks anymore, which happens constantly on 1980s and 1990s systems, the fix is often fabricated in the truck. That’s old-school blacksmithing applied to a modern driveway gate, and it’s a big part of why North Hollywood property owners call us instead of a generalist handyman.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Hollywood
On the automation side, we’re trained and equipped on nine major North Hollywood Gate Motor & Opener brands, and for North Hollywood’s older stock the ones we see most are FAAC, BFT, and Linear. If your 1989 FAAC slide operator is tripping its thermal overload on a hot afternoon, we can diagnose whether it’s the motor, the capacitor, or a dragging gate overloading the circuit. We stock common replacement parts for the older FAAC and BFT boards and limit switch assemblies, plus the heavy-gauge hinge and roller hardware this area’s gates depend on. Whatever the brand, the repair gets quoted before we turn a bolt.
Common Gate Parts & Welding Problems We See in North Hollywood Homes
- Flat-spotted bottom rollers on slide gates. In the 91601-91603 apartment courts, concrete driveways act like heat sinks and routinely exceed 140°F in summer. Original polyurethane rollers from the 1980s and 1990s sit on that heat for decades, flat-spot, and the gate starts dragging until the operator draws too many amps and trips. We replace them with a harder compound and set the gate’s weight properly on the track.
- Steel slide tracks that bind mid-cycle. A slide gate that runs fine all morning and then stalls at 3:00 PM in North Hollywood is usually a heat-expansion problem. The track itself grows in the afternoon heat and binds the gate. The fix is a reset of rail clearance, sometimes a cut-and-reweld, which a cooler coastal tech rarely has to consider.
- Sagging hinge posts on 1950s-1970s bungalow swing gates. The post footing cracks away from the walkway over time, and the gate panel pulls the post inward on every open and close. We re-set or replace the post, weld a base gusset, and bring the gate back to level so it latches cleanly.
- Rusted-through post feet on older apartment gates. At the base, where steel meets damp soil and sprinkler overspray, the post rusts. We cut out the rot and weld in custom steel repair plates, then coat the work so it doesn’t rust through again in two years.
Pricing for Gate Parts & Welding in North Hollywood, CA
Here’s what North Hollywood homeowners can typically expect. Hinge replacement on a single swing gate runs $240-$420 per hinge, depending on whether the post needs resetting. Post replacement usually runs $380-$750 for a standard bungalow hinge post, more if the footing has to be re-poured deeper. Rail repair and re-welding a slide track spans $300-$800 depending on how much track has to be cut out. Custom welding, like a rusted post foot plate or a latch keeper repair, runs $180-$400 for most single-piece fabrications. A full set of replacement bottom rollers on an apartment slide gate typically runs $150-$300 installed. Every job is quoted in writing before work begins, and we honor that quote. Call (925) 307-8328 for a free estimate and a window that works around shared driveway access.
We Also Serve Cities Near North Hollywood
Our crews work all over the San Fernando Valley and the edges of the Verdugos. Beyond North Hollywood, we regularly take gate parts and welding calls in Sun Valley, Van Nuys, Panorama City, and Tujunga. If your gate is acting up and you’re a few miles from NoHo proper, call us. Same crew, same 90-Day Done Right Promise, same straight answer on the phone.
Serving North Hollywood, CA - Our Local Coverage Area
We’re based in the North Hollywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in North Hollywood
Because your concrete driveway holds heat. On hot Valley days, that slab can exceed 140°F, and the original polyurethane rollers on 1980s and 1990s slide gates soften, flat-spot, and crack. Once they flat-spot, the gate drags, the operator works harder, and eventually the thermal overload trips. The permanent fix is to replace them with a harder compound rated for sustained heat and re-set the gate’s weight on the track so the load spreads across all the rollers, not just the ones nearest the motor. Call (925) 307-8328 and we’ll inspect what’s on the ground.
Yes, in most cases. The fix depends on the post footing. If the concrete around the post is still intact and only the post itself has cracked or pulled loose, we can cut the old post at the base, set a new one in the existing footing, and weld a steel gusset plate for lateral strength, no walkway demolition needed. If the footing itself has cracked, we may need to cut a small section of walkway and re-pour around the new post. Either way, we’ll show you exactly what’s required and quote it before any work starts.
We plan the work around the gate’s role as the only vehicle access. On a shared driveway off Lankershim Boulevard, for example, we replaced the bottom rollers and re-welded the rack and pinion on a 1989 DoorKing slide gate that was tripping its thermal overload every afternoon. Because that gate was the only vehicle access to six bungalows, our crew set up a temporary swing-gate opening using the old hinge post reinforcement so residents could keep coming and going while the slide track was cut out and re-welded. We’ll do the same for your court: access stays open, and the work gets done right.
Start by checking the gate’s travel, not the operator. The 3:00 PM overload is usually mechanical: the steel track has expanded in the afternoon heat and bound the gate, or the rollers are dragging, or both. We free the gate, re-set the rail clearance, replace any flat-spotted rollers, and then re-test the operator’s amp draw. A lot of times the motor and board are fine; the gate was just fighting the track. We’ll quote the mechanical fix first, and only touch the operator if it’s actually needed. Estimates are free at (925) 307-8328.
Yes, this is a standard repair for us. We cut out the rusted section at the post’s base, weld in a custom-fabricated steel plate sized to that specific post, and coat the repair so it resists future corrosion from sprinklers and soil moisture. It’s stronger than the original post foot when we’re done, and it’s covered by the 90-Day Done Right Promise. If you’ve got an apartment gate with a post that’s visibly rusted at the ground line, call us at (925) 307-8328 for a look.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Gate Parts & Welding in North Hollywood. If your gate is dragging, sticking, or sagging, call (925) 307-8328 for a free estimate and an honest answer.